try to fix submodule

firmware/lib/Arduino-FOC-drivers/examples/encoders/smoothing/smoothing.ino

@@ -0,0 +1,141 @@
+/**
+ *
+ * Hall sensor velocity motion control example, modified to demonstrate usage of SmoothingSensor
+ * Steps:
+ * 1) Configure the motor and sensor
+ * 2) Run the code
+ * 3) Set the target velocity (in radians per second) from serial terminal
+ * 4) Try with and without smoothing to see the difference (send E1 and E0 commands from serial terminal)
+ *
+ *
+ *
+ * NOTE :
+ * > Specifically for Arduino UNO example code for running velocity motion control using a hall sensor
+ * > Since Arduino UNO doesn't have enough interrupt pins we have to use software interrupt library PciManager.
+ *
+ * > If running this code with Nucleo or Bluepill or any other board which has more than 2 interrupt pins
+ * > you can supply doC directly to the sensor.enableInterrupts(doA,doB,doC) and avoid using PciManger
+ *
+ */
+#include <SimpleFOC.h>
+// software interrupt library
+#include <PciManager.h>
+#include <PciListenerImp.h>
+#include <SimpleFOCDrivers.h>
+#include <encoders/smoothing/SmoothingSensor.h>
+
+// BLDC motor & driver instance
+BLDCMotor motor = BLDCMotor(11);
+BLDCDriver3PWM driver = BLDCDriver3PWM(9, 5, 6, 8);
+// Stepper motor & driver instance
+//StepperMotor motor = StepperMotor(50);
+//StepperDriver4PWM driver = StepperDriver4PWM(9, 5, 10, 6,  8);
+
+// hall sensor instance
+HallSensor sensor = HallSensor(2, 3, 4, 11);
+// wrapper instance
+SmoothingSensor smooth(sensor, motor);
+
+// Interrupt routine intialisation
+// channel A and B callbacks
+void doA(){sensor.handleA();}
+void doB(){sensor.handleB();}
+void doC(){sensor.handleC();}
+// If no available hadware interrupt pins use the software interrupt
+PciListenerImp listenerIndex(sensor.pinC, doC);
+
+// velocity set point variable
+float target_velocity = 0;
+// instantiate the commander
+Commander command = Commander(Serial);
+void doTarget(char* cmd) { command.scalar(&target_velocity, cmd); }
+
+void enableSmoothing(char* cmd) {
+  float enable;
+  command.scalar(&enable, cmd);
+  motor.linkSensor(enable == 0 ? (Sensor*)&sensor : (Sensor*)&smooth);
+}
+
+void setup() {
+
+  // initialize sensor sensor hardware
+  sensor.init();
+  sensor.enableInterrupts(doA, doB); //, doC);
+  // software interrupts
+  PciManager.registerListener(&listenerIndex);
+  // set SmoothingSensor phase correction for hall sensors
+  smooth.phase_correction = -_PI_6;
+  // link the SmoothingSensor to the motor
+  motor.linkSensor(&smooth);
+
+  // driver config
+  // power supply voltage [V]
+  driver.voltage_power_supply = 12;
+  driver.init();
+  // link the motor and the driver
+  motor.linkDriver(&driver);
+
+  // aligning voltage [V]
+  motor.voltage_sensor_align = 3;
+
+  // set motion control loop to be used
+  motor.controller = MotionControlType::velocity;
+
+  // contoller configuration
+  // default parameters in defaults.h
+
+  // velocity PI controller parameters
+  motor.PID_velocity.P = 0.2f;
+  motor.PID_velocity.I = 2;
+  motor.PID_velocity.D = 0;
+  // default voltage_power_supply
+  motor.voltage_limit = 6;
+  // jerk control using voltage voltage ramp
+  // default value is 300 volts per sec  ~ 0.3V per millisecond
+  motor.PID_velocity.output_ramp = 1000;
+
+  // velocity low pass filtering time constant
+  motor.LPF_velocity.Tf = 0.01f;
+
+  // use monitoring with serial
+  Serial.begin(115200);
+  // comment out if not needed
+  motor.useMonitoring(Serial);
+
+  // initialize motor
+  motor.init();
+  // align sensor and start FOC
+  motor.initFOC();
+
+  // add target command T
+  command.add('T', doTarget, "target voltage");
+
+  // add smoothing enable/disable command E (send E0 to use hall sensor alone, or E1 to use smoothing)
+  command.add('E', enableSmoothing, "enable smoothing");
+
+  Serial.println(F("Motor ready."));
+  Serial.println(F("Set the target velocity using serial terminal:"));
+  _delay(1000);
+}
+
+
+void loop() {
+  // main FOC algorithm function
+  // the faster you run this function the better
+  // Arduino UNO loop  ~1kHz
+  // Bluepill loop ~10kHz
+  motor.loopFOC();
+
+  // Motion control function
+  // velocity, position or voltage (defined in motor.controller)
+  // this function can be run at much lower frequency than loopFOC() function
+  // You can also use motor.move() and set the motor.target in the code
+  motor.move(target_velocity);
+
+  // function intended to be used with serial plotter to monitor motor variables
+  // significantly slowing the execution down!!!!
+  // motor.monitor();
+
+  // user communication
+  command.run();
+}